3134F Bulkhead Coupling Female X Female US Brass Pipe fittings & Adapters
3134F
| PART# | Pipe size | C | C1 | Size-B | L |
| 3000-02 | 1/8 | 7/8 | 15/16 | 5/8-18 | .96 |
| 3000L-02 | 1/8 | 7/8 | 15/16 | 5/8-18 | 1.50 |
| 3000-04 | 1/4 | 1″ | 1″ | 3/4-16 | .94 |
| 3000L-04 | 1/4 | 1″ | 1″-1/8 | 3/4-16 | 1.50 |
| 3000-06 | 3/8 | 1″-1/8 | 1″-1/4 | 1″-14 | 1.31 |
| 3000-08 | 1/2 | 1″-1/4 | 1″-3/8 | 1″-1/8 | 1.50 |
Interchangeability for reference
Parker :207ACBH-2 207ACBHS-2 207ACBH-4 207ACBHS-4 207ACBH-6 207ACBH-8 207ACBH-12 207ACBH-16*
Eaton : 1344 1345 1346 1351
Midland : 28-300 28-301 28-302 28-315*28-303 28-304
| Part # | A | B | Length (in.) |
| 28-300 | 1/8-27NPTF | 5/8-18 UNS | 1-1/2″ |
| 28-301 | 1/4-18 NPTF | 3/4-16 UNS | 15/16″ |
| 28-302 | 1/4-18 NPTF | 3/4-16 UNS | 1-1/2″ |
| 28-315* | 1/4-18 NPTF | 3/4-16 UNS | 1-1/2″ |
| 28-303 | 3/8-18NPTF | 1-14 UNS | 1-5/16″ |
| 28-304 | /2-14NPTF | 1-1/8-14UNS | 1-1/2″ |
attention please ：Quotations and delivery of non-stock items supplied on request. Configurations and dimen sions subject to change without notice. Additional information can be found in SAE J530 Automotive Pipe Fittings and SAE J531 Drain Plugs.
Brass Compression Fittings & Adapters
Applications
Compatible with copper, brass, aluminum and thermoplastic tubing for instrumentation, hydraulic and pneumatic systems like typical fluid air, oil, water, lubricant and other applications.
Note: When use with thermoplastic tubing, a brass insert is required for support.
Features
- Construction – Three piece unit: body, nut (available with long or short nut) and sleeve. Extruded and Forged Configuration.
- Vibration resistance – Fair vibration resistance with short nut, The long nut can be used for greater vibration application.
- Advantages – Low cost. Easy to assemble without special tube prep, no flaring.Broad selection of styles and sizes.
Specification
- Temperature Range: -65°F to +250°F (-53°C to +121°C) range at maximum operating pressures.
- Working Pressure: up to 2000 PSI with a 4:1 safety factor depending on tube sizes. When using plastic tubing, use the working pressure for type used.
Assembly Instructions
- Cut tubing to desired length.
- Slide nut and then sleeve on tube. Threaded end “A” of nut must face out.
- Insert tubing into fitting body. Be sure tubing is bottomed on fitting shoulder.
- Lubricate threads and assemble to fitting body.
- Tighten nut hand tight. From that point, tighten with a wrench the number of turns indicated in the chart (For Fractional Tubes) below.
|
TUBE SIZE
|
Additional Turns From Hand Tight
|
|
1/8” thru 1/4”
|
1-1/4
|
|
5/16”
|
1-3/4
|
|
3/8” thru 1”
|
2-1/4
|
US Brass Compression Fittings & Adapters
- Extruded Bar Stock, Hex Forging Blank, Fractional Tube Dia & NPT Thread Mainly.
Euro Brass Compression Fittings & Adapters
- Extruded Bar Stock, Round Forging Blank, Nickel-Plated, Metric Tube Dia & BSP Thread Mainly.
